DOI : https://doi.org/10.18517/ijaseit.10.4.12802

Stress-Strain Relationship of High-Performance Fiber-Reinforced Concrete using Silica Fume and Steel Fiber

- Krisnamurti (1), A Soehardjono (2), A Zacoeb (3), A Wibowo (4)
(1) Department of Civil Engineering, Faculty of Engineering, University of Jember, Jember 68121, Indonesia
(2) Department of Civil Engineering, Faculty of Engineering, University of Brawijaya, Malang 65145, Indonesia
(3) Department of Civil Engineering, Faculty of Engineering, University of Brawijaya, Malang 65145, Indonesia
(4) Department of Civil Engineering, Faculty of Engineering, University of Brawijaya, Malang 65145, Indonesia
Fulltext View | Download
How to cite (IJASEIT) :
Krisnamurti, -, et al. “Stress-Strain Relationship of High-Performance Fiber-Reinforced Concrete Using Silica Fume and Steel Fiber”. International Journal on Advanced Science, Engineering and Information Technology, vol. 10, no. 4, Aug. 2020, pp. 1604-9, doi:10.18517/ijaseit.10.4.12802.
Citation Format :
Disaster mitigation in the world of civil engineering can do by improving the performance of construction materials using High-Performance Fiber-Reinforced Concrete (HPFRC). The increasing performance of concrete materials positively affects the physical and mechanical properties of the concrete produced, including the modulus of elasticity. Many equations develop to calculate the distribution of stress-strain of concrete material, such as the Madrid Parabola Formula, Desay & Khrisnan Formula, Majewski Formula, Wang & Hsu Formula, and Saenz Formula. The purpose of this study is to investigate a stress-strain distribution equation and the elastic modulus of elasticity of HPFRC using Portland Pozzolana Cement (PPC) with variations in the composition of silica fume and steel fiber and also investigate the formula of the HPFRC stress-strain distribution. The study conduct using f 15 cm x 30 cm cylindrical specimens. The materials are PPC, sand, gravel, water, silica fume additives, superplasticizers, and Dramix @ 3D steel fiber. Silica fume used varies from 0.0% to 15.0% of the weight of cement. While the steel fiber varies from 0.2% to 1.4% of the volume of the concrete mixture. The compressive strength test carries out refers to ASTM C39/C39M-03, 2003. The stress-strain relationship of HPFRC is obtained from the axial deformation measurement using an extensometer. The results of the study compare with some well-known stress-strain relationship equation. From this study, the stress-strain relationship formula of Desay-Khrisnan is rather suitable for the concrete with W/B ratio variation, but not suitable for silica fume and steel fiber content variation.

A. S. Arya and A. Agarwal, Multi-Hazard Resistant New Construction or Reconstruction of BPL Houses in Flood-Prone Alluvial Areas. 2008.

NEHRP Consultants Joint Venture, "Program Plan for the Development of Collapse Assessment and Mitigation Strategies for Existing Reinforced Concrete Buildings," Nist Gcr 10-917-7, p. 100, 2010.

ACI 363R-10, Report on High-Strength Concrete. 2010.

ACI 363.2R-11, Guide to Quality Control and Assurance of High-Strength Concrete. 2011.

ACI 544.1R-96, State-of-the-Art Report on Fiber Reinforced Concrete, vol. 96. Washington, D.C.: American Concrete Institute, 1997.

P. Kmiecik and M. Kaminski, "Modelling of reinforced concrete structures and composite structures with concrete strength degradation taken into consideration," Arch. Civ. Mech. Eng., vol. XI, no. 3, pp. 623-636, 2011.

E. Hognestad, "A Study of Combined Bending and Axial Load in Reinforced Concrete Members," Bull. Ser. No. 399, p. 128, 1951.

D. Moldovan and C. Magureanu, "Stress-Strain Diagram for High Strength Concrete Elements in Flexure," in 3rd International Conference Advanced Composite Materials Engineering, 2010, no. October, pp. 4-8.

J. D. Carreira and K.-H. Chu, "Stress-Strain Relationship for Plain Concrete in Compression," ACI J. Proc., vol. 82, no. 6, pp. 797-804, 1985.

ASTM E6-07, Standard Terminology Relating to Methods of Mechanical Testing. 2007.

ASTM C 469-02, Standard Test Method for Static Modulus of Elasticity and Poisson's Ratio of Concrete in Compression. Washington, D.C.: American Society for Testing and Materials (ASTM), 2002.

ACI 211.1-91, Standard Practice for Selecting Proportions for Normal Heavyweight, and Mass Concrete (ACI 211.1-91) Reapproved 1997. Washington, D.C.: American Concrete Institute, 1997.

SNI 7656:2012, Tata cara pemilihan campuran untuk beton normal , beton berat dan beton massa. Jakarta: Badan Standardisasi Nasional - BSN, 2012.

ASTM C 39/C39M-03, Standard Test Method for Compressive Strength of Cylindrical Concrete Specimens. Washington, D.C.: American Society for Testing and Materials (ASTM), 2003.

SNI 03-1974-1990, Metode pengujian kuat tekan beton. Badan Standardisasi Nasional - BSN, 1990.

Bekaert, "Dramix@ 3D 80/60 BG Data Sheet," Dramix Data Sheet. p. 1, 2012.

Bekaert, Dramix Reinforcing the future. NV Bekaert SA, 2012.

ACI 363R-10, Report on High-Strength Concrete. 2010.

B. Graybeal and M. Davis, "Cylinder or Cube Strength Testing of 80 t0 200 MPa Ultra-High-Performance Fiber-Reinforced-Concrete," ACI Mater. J. vol. 105, no. November/December, pp. 603-609, 2008.

T. Noguchi, F. Tomosawa, K. M. Nemati, B. M. Chiaia, and A. R. Fantilli, "A practical equation for the elastic modulus of concrete," ACI Struct. J. vol. 106, no. 5, pp. 690-696, 2009.

Authors who publish with this journal agree to the following terms:

    1. Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal.
    2. Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgement of its initial publication in this journal.
    3. Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work (See The Effect of Open Access).