DOI : https://doi.org/10.18517/ijaseit.8.3.4465

Finite Element Analysis of Osteosynthesis Miniplate for the Reconstruction of Parasymphyseal Compound Fracture

Muslim Mahardika (1), Romario Aldrian Wicaksono (2), Maria Goreti Widiastuti (3), Budi Arifvianto (4), - Suyitno (5)
(1) Universitas Gadjah Mada
(2) Universitas Gadjah Mada
(3) Dr. Sardjito General Hospital
(4) Universitas Gadjah Mada
(5) Universitas Gadjah Mada
Fulltext View | Download
How to cite (IJASEIT) :
Mahardika, Muslim, et al. “Finite Element Analysis of Osteosynthesis Miniplate for the Reconstruction of Parasymphyseal Compound Fracture”. International Journal on Advanced Science, Engineering and Information Technology, vol. 8, no. 3, June 2018, pp. 652-6, doi:10.18517/ijaseit.8.3.4465.
Citation Format :
In the last two decades, the use of osteosynthesis miniplate has been growing to aid the healing process and reconstruction of fractured mandibular bone. In principle, the plate is used to provide stable fixation of the fractured bone tissue during the healing process and reconstruction. Based on earlier studies, it is noted that arrangements and geometry of the osteosynthesis miniplate played a critical role in determining the stability of the fractured mandibular bone, as well as the miniplate. In this research, a simulation with finite element method (FEM) was carried out to investigate the influence of the number of holes in an osteosynthesis miniplate on the stability of fractured mandibular bone and the corresponding miniplate after the implantation. For this purpose, a set of osteosynthesis miniplate with three different configurations was taken for simulation using a three-dimensional (3D) model of mandibular bone generated from the patient through computed tomography (CT). The result of the simulation showed that all the miniplates with three configurations tested were stable enough to prevent movement of fractured mandibular bone. Moreover, fixation with a pair of miniplates having four screw holes demonstrated the desired result; as indicated by the lowest value of displacement, pressure on the bone surface and pressure on the miniplate.

Thoma, K. H., “A historical review of methods advocated for the treatment of jaw fractures, with ten commandments for modern fracture treatment.” Am. J. Orthod. Oral Surg., vol. 30(8), pp. C399-C504, 1944.

N.H. Al-Tairi, M.M. Shoushan, M.M. Saad Khedr, S.E. Abd-alal, “Comparison of three-dimensional plate versus double miniplate osteosynthesis for treatment of unfavorable mandibular angle fractures.” Tanta Dental Journal, vol. 12, 89-98, 2015.

Y. Arai, E. Tammisalo, K. Iwai, K. Hashimoto, and K. Shinoda, “Development of a compact computed tomographic apparatus for dental use,” vol. 240, no. April, pp. 245-248, 1999.

L. Ganry, B. Hersant, J. Quilichini, P. Leyder, J.P. Meningaud, “Use of the 3D surgical modelling technique with open-source software for mandibular fibula free flap reconstruction and its surgical guides,” J Stomatol Oral Maxillofac Surg., vol. 118, pp. 197-202, 2017.

M. van Eijnatten, R. van Dijk, J. Dobbe, G. Streekstra, J. Koivisto, J. Wolff, “CT image segmentation methods for bone used in medical additive manufacturing,” Medical Engineering and Physics, vol. 51, pp. 6-16, 2018.

L. Ganry, J. Quilichini, C. M. Bandini, P. Leyder, B. Hersant, J. P. Meningaud, “Three-dimensional surgical modelling with an open- source software protocol: study of precision and reproducibility in mandibular reconstruction with the fibula free flap,” Int. J. Oral Maxillofac. Surg., vol. 46, pp. 946-957, 2017.

R. T. Hart, V. V Hennebel, and N. Thongpreda, “Modeling the biomechanics of the mandible: a three-dimensional finite element study *,” J. Biomech., vol. 25, no. 3, pp. 261-286, 1992.

T. Silagieva, A. Bucur, C. Gudas, S. Pituru, and O. Marius, “New miniplate for osteosynthesis of mandibular angle fractures designed to improve formation of new bone,” J. Cranio-Maxillofacial Surg., vol. 44, no. 4, pp. 500-505, 2016.

N. Narra et al., “Finite element analysis of customized reconstruction plates for mandibular continuity defect therapy,” J. Biomech., vol. 47, no. 1, pp. 264-268, 2014.

S. Albougha, K. Darwich, M. A. Darwich, M. H. Albogha, “Assessment of sagittal split ramus osteotomy rigid internal fixation techniques using a finite element method.” Int. J. Oral Maxillofac. Surg, vol. 44, pp. 823-829, 2015.

B. Spiessl, “Principles of rigid internal fixation in fractures of the lower jaw,” in new concepts in maxillofacial bone surgery, Springer, 1976, pp. 21-34.

R. Wang, Y. Liu, J. H. Wang, and D. A. Baur, “Effect of interfragmentary gap on the mechanical behavior of mandibular angle fracture with three fixation designs: A finite element analysis,” J. Plast. Reconstr. Aesthetic Surg., vol. 70, no. 3, pp. 360-369, 2016.

R. Gutwald, R. Scho, M. Metzger, K. Kreutzer, B. Rahn, and R. Schmelzeisen, “Miniplate osteosynthesis with four different systems in sheep,” pp. 94-102, 2011.

H. H. Korkmaz, “Evaluation of different miniplates in fixation of fractured human mandible with the finite element method,” Oral Surgery, Oral Med. Oral Pathol. Oral Radiol. Endodontology, vol. 103, no. 6, pp. 20-22, 2007.

R. Wang, Y. Liu, J. H. Wang, and D. A. Baur, “Effect of interfragmentary gap on the mechanical behavior of mandibular angle fracture with three fixation designs: A finite element analysis,” J. Plast. Reconstr. Aesthetic Surg., vol. 70, no. 3, pp. 360-369, 2017.

S. George, M. Wolf, R. Wendlandt, H. Kimmerle, P. Sieg, and H. Jacobsen, “Comparative biomechanical study on three miniplates osteosynthesis systems for stabilisation of low condylar fractures of the mandible,” Br. J. Oral Maxillofac. Surg., vol. 52, no. 4, pp. 317-322, 2014.

B. Ji, C. Wang, L. Liu, J. Long, and W. Tian, “A biomechanical analysis of titanium miniplates used for treatment of mandibular symphyseal fractures with the,” YMOE, vol. 109, no. 3, pp. e21-e27, 2010.

M. Champy, J. P. Loddi, R. Schmitt, J. H. Jaeger, and D. Muster, “Mandibular Osteosynthesis by Miniature Screwed Plates via a Buccal Approach *,” vol. 17, no. September 1976, pp. 14-21, 1978.

C. L. Schwartz-Dabney and P. C. Dechow, “Variations in cortical material properties throughout the human dentate mandible,” Am. J. Phys. Anthropol., vol. 120, no. 3, pp. 252-277, 2003.

M. Niinomi, “Mechanical properties of biomedical titanium alloys,” Mater. Sci. Eng. A, vol. 243, no. 1-2, pp. 231-236, 1998.

K. Harada, M. Watanabe, K. Ohkura, and S. Enomoto, “Measure of bite force and occlusal contact area before and after bilateral sagittal split ramus osteotomy of the mandible using a new pressure-sensitive device: a preliminary report,” J. oral Maxillofac. Surg., vol. 58, no. 4, pp. 370-373, 2000.

J. Tams, J.-P. Van Loon, B. Otten, and R. R. M. Bos, “A Computer Study of Biodegradable Plates for Internal Fixation of Mandibular,” J. Oral Maxillofac. Surg., vol. 59, pp. 404-407, 2001.

Authors who publish with this journal agree to the following terms:

    1. Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal.
    2. Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgement of its initial publication in this journal.
    3. Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work (See The Effect of Open Access).